Epson Stylus Photo R290 Скачать руководство пользователя страница 46

Страница: 46 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.4 Troubleshooting by Symptom

Printed image has
white banding.

Dirt on the CR shaft

Is there any dirt on the CR shaft?

Clean off any dirt on the CR shaft surface with a dry soft cloth.

PF Roller failure

Is there any dirt on the PF Roller?

Clean the PF Roller surface with a soft brush carefully so as not scratch
it.

Is the PF Roller damaged?

Replace the PF Roller.

Ink cartridge failure

Replace the ink cartridge with a new one, and print a nozzle check
pattern. The printed pattern has no missing dots?

The cartridge is defective. Use the new cartridge.

A malfunction of Carriage
movements

Are the carriage shaft and the Main Frame properly lubricated?

Apply G-71 grease referring to

“Lubrication of CR Unit”(p.116)

Improper platen gap

Is the platen gap (gap between the Printhead surface and the platen)
not properly set?

Adjust the platen gap properly.

Some gear(s) is (are) damaged.

Is (are) the gear(s) in the paper feed and ASF mechanisms
damaged?

Replace the damaged gear(s).

Dirt on the Printhead is preventing
nozzles from firing ink straight
toward the paper.

Run a cleaning cycle and make a test print. Repeat the operation
several times. Does the problem still appear?

Clean the Printhead surface with a cotton swab.

Is there any dust or foreign matter on the Cleaner Blade?

Remove any dust or foreign matter on the Cleaner Blade, or replace the
blade.

A malfunction of the Printhead

Run a cleaning cycle and make a test print. Repeat the operation
several times. Does the problem still appear?

Replace the Printhead.

CR shaft failure

Is the CR shaft not properly installed?

Reinstall the CR shaft properly.

Is the CR shaft surface damaged?

Replace the CR shaft.

Table 3-16. Troubleshooting Print Quality Problems

Symptom

Possible Cause

Check Point

Remedy

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 46 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: