Epson Stylus Photo R290 Скачать руководство пользователя страница 76

Страница: 76 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.4.4 APG Unit (Disassembling the Printer Mechanism)

Lubrication is required. See the page given below for the
lubrication information.

Lubrication of APG Unit (p.117)

Install the APG Unit following the procedure below.
1. Put a pin (thinner than Ø2mm) through the positioning

holes of the Main Frame and the right PG Cam on the CR
Shaft.

Figure 4-57. Reinstalling the APG Unit (1)

2. Put the pin through the positioning holes of the Spur gear

28.8 and the APG Unit.

Figure 4-58. Reinstalling the APG Unit (2)

Pin (1)

Positioning Hole

Right PG Cam

Spur Gear 28.8

APG Unit

Pin

Front: Positioning Hole of Spur Gear 28.8
Back: Positioning Hole of APG Unit

3. Install the APG Unit to the Main Frame.

Figure 4-59. Reinstalling the APG Unit (3)

4. Check that the hooks (

) are attached to the positioning

holes of the Main Frame, then screw the APG Unit.

Figure 4-60. Reinstalling the APG Unit (4)

Tighten the screws in the order given in

Fig.4-55 (p.75)

APG Unit

Pin

Main Frame

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 76 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: