Epson Stylus Photo R290 Скачать руководство пользователя страница 39

Страница: 39 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3 Troubleshooting by Error Message

Any time

The PF Motor drive force is not
transmitted to the LD Roller.

ASF Unit

3. Is the clutch damaged?

3. Replace the ASF Unit.

4.4.14 “ASF
Unit”(p.88)

4. Is the Compression Spring 2.36 of the Change

Lever detached?

4. Replace the ASF Unit.

The LD Roller shaft is not set in the
ASF home position, and paper is
always fed from the ASF Assy.

ASF Unit

1. Is the edge of the Change Lever chipped or

broken?

1. Replace the ASF Unit.

Table 3-9. Troubleshooting for No Paper Error

Occurrence

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

LD Roller

Clutch

ASF

Compression Spring2.36

Change Lever

CR Motor

Edge of Change Lever

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 39 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: