Epson Stylus Photo R290 Скачать руководство пользователя страница 56

Страница: 56 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.1.6 Required Preparation before Disassembly (Overview)

4.1.6 Required Preparation before Disassembly

Make sure to carry out the following operations before disassembling the printer.

When the Main Board needs to be replaced, make a backup copy of EEPROM
data.

Unlock the carriage lock and move the CR Unit to other than its home position.

•

“4.1.8 How to Unlock the Carriage”

4.1.7 Orientation Definition

Orientation descriptions used in the disassembly/reassembly procedures are as follows.

Figure 4-7. Orientation Definition

4.1.8 How to Unlock the Carriage

Unlocking the carriage is required for disassembly of some parts or components.
Carry out any of the following operations to unlock the carriage and move the
carriage to other than its home position.

Power the printer and turn it off forcedly by disconnecting the power cable
when the CR Unit is unlocked and moved away from the home position.

Turn the EJ Roller gear on the left side of the printer in the direction of the
arrow until the carriage is unlocked.

Figure 4-8. How to Unlock the Carriage

[Left Side]

[Right (home) Side]

[Rear Side]

[Front Side]

C A U T I O N

Be extremely careful not to damage the EJ Roller gear. Extra care
must be taken to avoid injury from sharp metal edges.

Carriage Lock

Locked

Carriage Lock

Unlocked

[Left side]

PF Roller Gear

EJ Roller Gear

Turn this gear

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 56 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: