manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 32 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 32

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3  Troubleshooting by Error Message

32

Table 3-5.  Troubleshooting for Fatal Error

Occurrence 

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

At power-on

• CR motor does not 

rotate at all.

• CR Unit hits against 

the right side of the 
Main Frame.

CR Motor

1. Is the CR motor cable not connected to CN14 on 

the Main Board?

1. Connect the cable correctly.

4.3.1 “Main Board 
Unit”(p.61)

2. Is there a malfunction of the CR motor?

2. Replace the CR motor.

4.4.12 “CR Motor”(p.84)

Main Frame

1. Is their any dirt on the Main Frame? Or is the 

frame not adequately lubricated?

1. Clean off any dirt on the frame and apply 

adequate grease on it.

6.1.3 "Lubrication" 
(P.114)

CR Guide Shaft

1. Is their any dirt on the CR Guide Shaft? Or is the 

shaft not adequately lubricated?

1. Clean off any dirt on the shaft and apply 

adequate grease on it.

6.1.3 "Lubrication" 
(P.114)

2. Is the PG cam chipped or broken?

2. Replace the CR Guide Shaft.

4.4.13 “CR Unit”(p.86)

CR Encoder

1. Is the Head FFC not connected to the CR encoder 

connector?

1. Connect the Head FFC to the connector 

correctly.

2. Is the CR encoder chipped or broken?

2. Replace the CR Unit.

Head FFC

1. Is the Head FFC broken?

1. Replace the Head FFC.

CR Scale

1. Is the CR Scale not moving freely, centered 

between the sides of CR encoder sensor?

1. Install the CR Scale correctly.

4.4.3 “CR Scale”(p.74)

2. Is there any dirt on the CR Scale?

2. Clean off any dirt on the CR Scale. If the scale 

get heavily soiled, replace the scale.

3. Is the CR Scale chipped or broken?

3. Replace the CR Scale.

Timing Belt

1. Is the Timing Belt attached incorrectly?

1. Attach the belt correctly.

4.4.13 “CR Unit”(p.86)

 / 

4.4.12 “CR Motor”(p.84)

PG Cam

CR Shaft

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов