Epson Stylus Photo R290 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 125

Epson Stylus Photo R290 Скачать руководство пользователя страница 92

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.4.17 Front Paper Guide Assy (Disassembling the Printer Mechanism)

92

4.4.17 Front Paper Guide Assy

Parts/Components need to be removed in advance

Printer Cover / Paper Support Assy / Upper Housing / Main Board Unit / Panel Assy /
Cover Open Sensor / Printer Mechanism / Ink System / CR Motor / PF Encoder / PF
Scale / PF Motor / EJ Frame Assy / APG Unit / CR Unit / ASF Unit / Upper Paper
Guide

Removal procedure

1.

Remove the screw and remove the Parallelism Bushing L.

•

Screw

: C.B.S.(P2) M3x8 (tightening torque: 6-8 kgf.cm)

Figure 4-107. Removing the Parallelism Bushing L

2.

Disconnect the connector of the PE Sensor Cable on the rear side of the
printer.

3.

Remove the screw that secures the Front Paper Guide Assy.

•

Screw

: C.B.S. M3x6 (tightening torque: 7-9 kgf.cm)

Figure 4-108. Removing the PE Sensor Cable

4.

Pull out the EJ Ground Spring to the front side.

Figure 4-109. Removing the EJ Ground Spring

C A U T I O N

Do not touch the surface of the rubber roller of the EJ Roller Assy
and the coated part of the PF Roller Assy as it can adversely affect
the print quality.

Parallelism Bushing L

Front Paper Guide Assy

[Rear Side]

Positioning Hole and Guide Pin

PE Sensor Cable

Connector

Front Paper Guide Assy

Front Paper Guide Assy

EJ Ground Spring

«
...
90
91
92
93
94
...
»

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов