Epson Stylus Photo R290 Скачать руководство пользователя страница 72

Страница: 72 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.4.2 Printhead (Disassembling the Printer Mechanism)

4.4.2 Printhead

Parts/Components need to be removed in advance

Printer Cover / Paper Support Assy / Upper Housing

Removal procedure

Move the CR Unit to the center, open the Cartridge Cover and remove all Ink
Cartridges.

While disengaging the hook of the Head FFC Cover with a flathead
screwdriver, slide the Head FFC Cover downward and remove it.

Figure 4-45. Removing the Head FFC Cover

Disconnect the CSIC FFC from the connector (

) on the CSIC Board.

Figure 4-46. Removing the CSIC FFC

While disengaging the hook of the Head FFC Cover Inner with a flathead
screwdriver, slide the Head FFC Cover Inner upward and remove it.

Figure 4-47. Removing the Head FFC Cover Inner

C A U T I O N

When removing the Head FFC Cover and the Head FFC
Cover Inner, do not use tools with sharp ends as the FFC may
get damaged.

Be careful not to damage the FFC and cables when
disengaging the hook of the CSIC Assy.

C H E C K

P O I N T

See the section given below on how to unlock the carriage.

•

“4.1.8 How to Unlock the Carriage”

Head FFC Cover

Hook

Removal Direction

Screwdriver

CSIC FFC

Removal Direction

Screwdriver

Hook

Head FFC Cover Inner

Содержание Stylus Photo R290






























































































































Результаты поиска

Содержание Stylus Photo R290

Отзывы:

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 72 / 125

Результаты поиска

Содержание Stylus Photo R290

Отзывы: