Epson SC-F10000 Series Скачать руководство пользователя страница 125

Страница: 125 / 222

Raise the ink cartridge cover.

Repeat the opening, shaking and replacement
procedures to replace other ink cartridges.

Replace the wiper roll

Preparing and Replacement Timing

When a message is displayed indicating the time to
replace the wiper roll is approaching

Prepare a new wiper roll as soon as possible.

When you want to replace the parts at this stage, such as
due to night operations, execute

Maintenance

Replace Maintenance Parts

Replace Wiper Roll

, and

then do the replacement work. If you replace it without
selecting

Replace Wiper Roll

, the wiper roll counter will

not operate correctly.

Maintenance

“Maintenance menu” on page 167

When a message is displayed indicating it is time to
replace the wiper roll

See the following section, and replace the wiper roll.
Printing cannot be performed if the parts are not
replaced.

Make sure you use a replacement wiper roll for this
printer.

“Options and Consumable Products” on

page 179

Before starting this procedure, be sure to read the
following.

“Precautions regarding maintenance” on

page 106

Replacement procedure

Check the on-screen message, and then press

Start

Lower the lock release lever to open the right-side
maintenance cover.

Pull the lock lever, and then pull the wiper unit
out at an upward angle.

Place the wiper unit on a flat place oriented as
shown in the illustration.

SC-F10000H Series/SC-F10000 Series User's Guide

Maintenance

125

Содержание SC-F10000 Series































































































































































































































Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Похожие инструкции для SC-F10000 Series

Бренды по названию

Популярные бренды

Epson SC-F10000 Series, Руководство пользователя

Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Похожие инструкции для SC-F10000 Series

Бренды по названию

Популярные бренды