Epson SC-F10000 Series Скачать руководство пользователя страница 106

Страница: 106 / 222

What You’ll Need

Ready the following items before beginning cleaning
and replacement.

When the supplied parts have been completely used,
purchase new consumables.

Prepare genuine parts when replacing ink cartridges or
performing maintenance.

“Options and Consumable Products” on

page 179

If your gloves have worn out, prepare commercially
available nitrile gloves.

Protective eyeglasses (available in the market)

Protects your eyes from ink and cleaning fluid.

Mask (available in the market)

Protects your nose and mouth from ink and cleaning
fluid.

Cleaning kit (supplied with the printer)

Use these when wiping up ink stains.

The following accessories are in the kit.

Cleaning fluid (x1)

Cup (x1)

Gloves (x16)

Cleaning stick (x50)

How to use

“Using Cleaning liquid” on page 110

Metal or plastic (PP or PE) tray (available in the
market)

Use when putting cleaning utensils, removed
consumables, or cleaning fluid moved to the container
supplied with the printer.

Media Cleaner Brush (supplied with the printer)

Use when cleaning with media cleaner.

Soft cloth (available in the market)

Use when cleaning inside the front cover and the
bottom of the dryer. Use material that is not likely to
generate lint or static electricity.

Precautions regarding
maintenance

Note the following points when cleaning and replacing
parts.

SC-F10000H Series/SC-F10000 Series User's Guide

Maintenance

106

Содержание SC-F10000 Series































































































































































































































Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Похожие инструкции для SC-F10000 Series

Бренды по названию

Популярные бренды

Epson SC-F10000 Series, Руководство пользователя

Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Похожие инструкции для SC-F10000 Series

Бренды по названию

Популярные бренды