Epson SC-F10000 Series Скачать руководство пользователя страница 209

Страница: 209 / 222

Green

Yellow

Red

Status

Explanation

Off

Power off

The power is off.

Off

Flashing

Off

Starting/stopping
operations

Doing start up operations after the
power is turned on, or doing shut down
operations after the power is turned off.

Off

Idling

Idling in a normal state. Ready to print.

Flashing

Off

Printing

Printing in a normal state.

Off

Consumable near end
(idling)

Printing is possible, but printing will not
be possible when the consumables
need to be replaced.

Flashing

Off

Consumable near end
(printing)

Printing can continue, but printing will
stop and not be possible when the
consumables need to be replaced.

Off

Printing cannot start

Printing not possible in current state for
such reasons as a cover is open or a
consumable is not loaded.

Off

Error (recoverable)

An error has occurred so printing is not
possible. Resolve the error and printing
can be done.

Off

Flashing

Fatal error (service call)

An error has occurred that cannot be
resolved, so printing is not possible.

Flashing

Off

Doing maintenance (jobs
can be received)

A maintenance function is being
executed. Print jobs can be received.

Off

Flashing

Off

Doing maintenance (jobs
cannot be received)

A maintenance function is being
executed. Print jobs cannot be
received.

Off

Pause mode (printing
stopped)

Printing is stopped.

Flashing

Off

Pause mode (waiting to
stop printing)

Waiting to stop printing. Printing
continues to the end of the page, and
then stops.

Off

Offline (jobs cannot be
received)

The connection to the computer is
offline. Print jobs cannot be received.

SC-F10000H Series/SC-F10000 Series User's Guide

Appendix

209

Содержание SC-F10000 Series































































































































































































































Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Бренды по названию

Популярные бренды

Epson SC-F10000 Series, Руководство пользователя

Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Бренды по названию

Популярные бренды