Epson SC-F10000 Series Скачать руководство пользователя страница 6

Страница: 6 / 222

Notes on Manuals

Meaning of Symbols

Warning:

Warnings must be followed to
avoid serious bodily injury.

Caution:

Cautions must be followed to
avoid bodily injury.

Important:

Important must be followed to
avoid damage to this product.

Note:

Notes contain useful or
additional information on the
operation of this product.

Indicates related reference
content.

Screenshots in This
Manual

❏

The screenshots in this manual may differ slightly
from the real screens.

❏

The screenshots of the control panel in this manual
are set to have

Black

backgrounds.

Illustrations

❏

The illustrations in this manual are of the
SC-F10000 Series, unless otherwise specified.

❏

The illustrations in this manual may differ slightly
from the model you are using.

Manual Organization

North America

To view user manuals, visit:

SC-F10070H:

❏

www.epson.com/support/f10070h

(U.S.)

❏

www.epson.ca/support/f10070h

(Canada)

SC-F10070:

❏

www.epson.com/support/f10070

(U.S.)

❏

www.epson.ca/support/f10070

(Canada)

Latin America

To view user manuals, visit:

SC-F10070H:

❏

www.latin.epson.com/support/f10070h

(Caribbean)

❏

www.epson.com.br/suporte/f10070h

(Brazil)

❏

www.latin.epson.com/soporte/f10070h

(other

regions)

SC-F10070:

❏

www.latin.epson.com/support/f10070

(Caribbean)

❏

www.epson.com.br/suporte/f10070

(Brazil)

❏

www.latin.epson.com/soporte/f10070

(other

regions)

Other Regions

The manuals for the product are organized as shown
below.

You can view the PDF manuals using Adobe Acrobat
Reader or Preview (Mac).

SC-F10000H Series/SC-F10000 Series User's Guide

Notes on Manuals

Содержание SC-F10000 Series































































































































































































































Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Похожие инструкции для SC-F10000 Series

Бренды по названию

Популярные бренды

Epson SC-F10000 Series, Руководство пользователя

Результаты поиска

Содержание SC-F10000 Series

Отзывы:

Похожие инструкции для SC-F10000 Series

Бренды по названию

Популярные бренды