Endress+Hauser Proline t-mass 65 MODBUS RS485 Скачать руководство пользователя страница 16

Страница: 16 / 62

QUICK SETUP

Proline t-mass 65 MODBUS RS485

Hauser

5.3

Quick Setup "Sensor"

It is essential that the insertion sensor is setup according to the actual pipe or duct and then installed
at the calculated insertion depth. This Quick Setup guides you systematically through the procedure
to setup the sensor.

Note!
The QUICK SETUP SENSOR function is not available for flanged type sensors.

A0009910-en

PIPE TYPE

• CIRCULAR

– in case that the pipe is of a standard type, then parameterize functions PIPE STANDARD and NOMINAL

DIAMETER

– In case that the pipe is a non-standard type, then select OTHERS in the function PIPE STANDARD and

parameterize the functions WALL THICKNESS and OUTER DIAMETER.

– The function INTERNAL DIAMETER displays the calculated internal diameter and is read only.

• RECTANGULAR

– Enter the INTERNAL HEIGHT, INTERNAL WIDTH and WALL THICKNESS of the duct
– Select the MOUNTING orientation of the sensor: HORIZONTAL or VERTICAL

MOUNTING SET LENGTH

Enter the measured length of the mounting set (including the compression fitting).

INSERTION DEPTH

This function calculates the insertion depth value for the mounting of the sensor.
This function is read only.

Press

to save settings and return to QUICK SETUP SENSOR group.

Esc

XXX.XXX.XX

HOME-POSITION

INSERTION

DEPH

MOUNTING SET

LENGTH

QUICK SETUP

SENSOR

PIPE

STANDARD

INTERNAL

HEIGHT

NOMINAL

DIAMETER

INTERNAL

WIDTH

UNIT

LENGTH

WALL

THICKNESS

WALL

THICKNESS

MOUNTING

RECTANGULAR

CIRCULAR

OUTER

DIAMETER

INTERNAL
DIAMETER

PIPE

TYPE

Selection Pipe Type

Содержание Proline t-mass 65 MODBUS RS485































































Результаты поиска

Содержание Proline t-mass 65 MODBUS RS485

Отзывы:

Похожие инструкции для Proline t-mass 65 MODBUS RS485

Бренды по названию

Популярные бренды

Endress+Hauser Proline t-mass 65 MODBUS RS485, Руководство пользователя

Результаты поиска

Содержание Proline t-mass 65 MODBUS RS485

Отзывы:

Похожие инструкции для Proline t-mass 65 MODBUS RS485

Бренды по названию

Популярные бренды