Endress+Hauser Proline Promag 10 Скачать руководство пользователя страница 86

Страница: 86 / 124

10 Technical data

PROline Promag 10

Hauser

Promag H

Transmitter housing:

•

Compact housing: powder-coated die-cast aluminum

•

Remote version housing: powder-coated die-cast aluminium

Sensor housing: 1.4301
Wall mounting kit (holding plate): 1.4301

Measuring tube: stainless steel 1.4301 or 1.4306/304L

Flanges: connections generally made of 1.4404/316L

Ground rings: 1.4435/316L, Alloy C-22

Electrodes:

•

Standard: 1.4435

•

Optional: Alloy C-22

Seals:

•

DN 2...25: O-ring (EPDM, Viton, Kalrez) or moulded seal (EPDM, silicone, Viton)

•

DN 40...100: moulded seal (EPDM, silicone)

Material load diagram

The material load diagrams (pressure-temperature graphs) for the process connections
are to be found in the following documents:

•

Technical Information “Promag 10 W” (TI 093D/06/en)

•

Technical Information “Promag 10

P” (TI 094D/06/en)

•

Technical Information “Promag 10 H” (TI 095D/06/en)

Fitted electrodes

Promag W:
Measuring electrodes, reference electrodes and Empty Pipe Detection electrodes
Available as standard with: 1.4435/316L, Alloy C-22

Promag P:
Measuring electrodes, reference electrodes and Empty Pipe Detection electrodes
Available as standard with: 1.4435/316L, Alloy C-22

Promag H:
Measuring electrodes and Empty Pipe Detection electrodes

•

Available as standard with: 1.4435/316L, Alloy C-22

•

DN 2...4: without Empty Pipe Detection electrode

Process connection

Promag W:
Flange connection: DIN (dimensions to DIN 2501), ANSI, JIS

Promag P:
Flange connection: DIN (dimensions to DIN 2501), ANSI, JIS

Promag H:

•

With O-ring: flange (DIN, ANSI, JIS), external thread (ISO 228/DIN299)

•

With moulded seal: weld socket (DIN 11850, ODT), Tri-Clamp,
threaded joint (DIN 11851, DIN 11864-1, SMS1145), flange DIN 11864-2

Surface roughness

•

Measuring tube lining with PFA:

≤

0.3

m (Promag H)

•

Electrodes:
1.4435/316L, Alloy C-22:

≤

0.4

•

Promag H process connection:

≤

0.8

(All data refer to parts in contact with medium)

Содержание Proline Promag 10





























































































































Результаты поиска

Содержание Proline Promag 10

Отзывы:

Похожие инструкции для Proline Promag 10

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 10, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag 10

Отзывы:

Похожие инструкции для Proline Promag 10

Бренды по названию

Популярные бренды