Endress+Hauser Proline Promag 10 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 124

background image

PROline Promag 10

3 Installation

Hauser

11

Transporting flanged devices (DN

≥

350):

Use only the metal eyes on the flanges

for transporting the device, lifting it and

positioning the sensor in the piping.

"

Caution!
Do not attempt to lift the sensor with the tines of a fork-lift truck beneath the metal casing.
This would buckle the casing and damage the internal magnetic coils.

Fig. 4:

Transporting sensors with DN

≥

350

3.1.3

Storage

Note the following points:

•

Pack the measuring device in such a way as to protect it reliably against impact for
storage (and transportation). The original packaging provides optimum protection.

•

The permissible storage temperature is

−

10...+50 °C (pref20 °C).

•

Do not remove the protective covers or caps on the process connections until you are
ready to install the device. This is particularly important in the case of sensors with
Teflon linings.

•

The measuring device must be protected against direct sunlight during storage in
order to avoid unacceptably high surface temperatures.

•

Choose a storage location where moisture does not collect in the measuring device.
This will help prevent fungus and bacteria infestation which can damage the liner.

F06

-1

0Fx

xx

xx

-22-

xx

-x

x

-xx

-0

01

«
...
9
10
11
12
13
...
»

Содержание Proline Promag 10





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 10

Бренд: TaiDoc Страницы: 31

Бренд: Aaronia Страницы: 47

Бренд: ETI Страницы: 2

Бренд: Nidec-Shimpo Страницы: 6

Бренд: U.S. Solid Страницы: 30

OMCL-AC240TS-R3

Бренд: Olympus Страницы: 3

Бренд: OHAUS Страницы: 6

Бренд: E+E Elektronik Страницы: 20

Бренд: Brooks Страницы: 64

Бренд: brena Страницы: 26

DistanceMaster Compact

Бренд: LaserLiner Страницы: 14

Бренд: inbody Страницы: 36

Retinomax K+Screeen

Бренд: Righton Страницы: 112

Бренд: Televes Страницы: 2

Бренд: MFJ Страницы: 8

Бренд: Anslut Страницы: 11

Бренд: Silverline Страницы: 2

Бренд: OfiTE Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды