Endress+Hauser Micropilot S FMR530 Скачать руководство пользователя страница 82

Страница: 82 / 92

Technical data

Micropilot S FMR533 4 to 20 mA HART

Hauser

10.1.7

Operating conditions: Process

Process temperature range

-40 °C to +200 °C

Process pressure limits

0 to 40 bar (Option 64 bar)

Dielectric constant

• In a stilling well:

≥

1.4

• In free space:

≥

1.9

10.1.8

Mechanical construction

Weight

Approx 6 kg + weight of flange

Material

Refer to TI00344F/00/EN, chapter "Material (not in contact with process)" and "Material (in
contact with process)".

10.1.9

Certificates and approvals

CE approval

The measuring system meets the legal requirements of the EC-guidelines.
Hauser confirms the device passing the required tests by attaching the CE-mark.

RF approvals

R&TTE 1999/5/EG, FCC CRF 47, part 15

Custody type approval

All aspects of OIML R85 are fulfilled.

Overspill protection

WHG, see ZE00243F/00/DE.

External standards and
guidelines

To conception and development for Micropilot S have been followed the external standards and
guidelines:

EN 60529

Protection class of housing (IP-code)

EN 61010

Safety regulations for electrical devices for measurement, control, regulation, and laboratory use.

EN 61326

Emissions (equipment class B), compatibility (appendix A – industrial area)

NAMUR

Standards committee for measurement and control in the chemical industry

API (American Petroleum Institute)

Particularly "Manual of Petroleum Measurement Stadards".

OIML R85 (Organisation Internationale de Métrologie Légale)

Ex approval

XA00081F-B
Safety Instructions for Micropilot S FMR530, FMR532, FMR533
(T12 / EEx ia IIC T6…T1)
PTB 00 ATEX 2067 X, Equipment marking: (II 1/2 G)

Marine certificate

GL (Germanischer Lloyd)

Содержание Micropilot S FMR530





























































































Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot S FMR530, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды