Endress+Hauser Micropilot S FMR530 Скачать руководство пользователя страница 73

Страница: 73 / 92

Micropilot S FMR533 4 to 20 mA HART

Trouble-shooting

Hauser

Error

Output

Possible cause

Remedy

If the surface is not
calm (e.g. filling,
emptying, agitator
running), the
measured value
jumps sporadically
to a higher level

L00-FMR53xxx-19-00-00-en-008

Signal is weakened by
the rough surface — the
interference echoes
are sometimes stronger

Carry out tank mapping

→

basic

setup

Set the process cond. (004) to
"turb. surface" or "agitator

Increase the output damping
(058)

Optimise the orientation
(

→

74)

If necessary, select a better
mounting position and/or larger
antenna (

→

11)

During filling/
emptying the
measured value
jumps sporadically
to a higher/lower
level

L00-FMR53xxx-19-00-00-en-009

During definition of the
auto correction table
the device has been
switched off and the
level has changed.

Reset "555"

Iff possible, do not switch off the
device before the complete
measuring range has been passed
through.

During filling/
emptying the
measured value
jumps downwards

L00-FMR53xxx-19-00-00-en-004

Multiple echoes

yes

→

Check the tank shape (002),
e.g. "dome ceiling" or
"horizontal cyl"

In the range of the blocking dist.
(059) there is no echo evaluation

→

Adapt the value

If possible, do not select
central installation position
(

→

11)

Activate auto correktion (031)

E641

((loss ofecho)

L00-FMR53xxx-19-00-00-en-005

Level echo is tooweak.

Possible causes:
• Rough surface dueto

filling/emptying

• Agitator running
• Foam

yes

→

Check application parameters
(002), (003) and (004)

Optimise alignment (

→

74)

If necessary, select a better
installation position and/or larger
antenna (

→

11)

E641

(loss ofecho)

after turn onthe
power supply

If the device is configured to Hold by lossof echo
the output is set to anyvalue/current.

noise level during
theinitialisation phase
tohigh.

Repeat once more empty calibr.
(005).

Caution!
Before conformation change with

to the edit mode.

20 mA/100%

4 mA/0%

→

actual

expected

20 mA/100%

4 mA/0%

→

expected

actual

20 mA/100%

4 mA/0%

→

expected

actual

20 mA/100%

E 641

4 mA/0%

→

actual

expected

Содержание Micropilot S FMR530





























































































Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot S FMR530, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды