Endress+Hauser Micropilot S FMR530 Скачать руководство пользователя страница 33

Страница: 33 / 92

Micropilot S FMR533 4 to 20 mA HART

Operation

Hauser

5.3

Local operation

5.3.1

Locking of the configuration mode

The Micropilot can be protected in two ways against unauthorised changing of device data,
numerical values or factory settings:

Function "unlock parameter" (0A4):

A value

<> 100

(e.g. 99) must be entered in "

unlock parameter

(0A4)

in the "

diagnostics

(0A)

function group. The lock is shown on the display by the

symbol and can be released again either

via the display or by communication.

Hardware lock:

The device is locked by pressing the

and

keys at the same time.

The lock is shown on the display by the

symbol and can

only

be unlocked again via the display

by pressing the

and

keys at the same time again. It is

not

possible to unlock the hardware

by communication. All parameters can de displayed even if the device is locked.

⇒

and

press simultaneous

⇓

The LOCK_SYMBOL appears on the LCD

E HAUSER

–

Содержание Micropilot S FMR530





























































































Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot S FMR530, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды