Endress+Hauser Micropilot S FMR530 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 92

background image

Safety instructions

Micropilot S FMR533 4 to 20 mA HART

4

Hauser

1

Safety instructions

1.1

Designated use

The Micropilot S is a compact radar level transmitter for the continuous, contactless measurement
of liquids. The device can also be freely mounted outside closed metal vessels because of its
operating frequency of about 6 GHz and a maximum radiated pulsed energy of 1 mW (average
power output 1

μ

W). Operation is completely harmless to humans and animals.

1.2

Installation, commissioning and operation

The Micropilot S has been designed to operate safely in accordance with current technical, safety
and EU standards. If installed incorrectly or used for applications for which it is not intended,
however, it is possible that application-related dangers may arise, e.g. product overflow due to
incorrect installation or calibration. For this reason, the device must be installed, connected,
operated and maintained according to the instructions in this manual: personnel must be authorised
and suitably qualified. The manual must have been read and understood, and the instructions
followed. Modifications and repairs to the device are permissible only when they are expressly
approved in the manual.

1.3

Operational safety and process safety

Alternative monitoring measures must be taken to ensure operational safety and process safety
during configuration, testing and maintenance work on the device.

1.3.1

Hazardous areas

Measuring systems for use in hazardous environments are accompanied by separate "Ex
documentation", which is an integral part of this Operating Manual. Strict compliance with the
installation instructions and ratings as stated in this supplementary documentation is mandatory.

• Ensure that all personnel are suitably qualified.
• Observe the specifications in the certificate as well as national and local regulations.

1.3.2

FCC-approval

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1.

This device may not cause harmful interference, and

2.

this device must accept any interference received, including interference that may cause
undesired operation.

"

Caution!
Changes or modifications not expressly approved by the part responsible for compliance could void
the user’s authority to operate the equipment.

«
...
2
3
4
5
6
...
»

Содержание Micropilot S FMR530





























































































Отзывы:

Нет отзывов

Похожие инструкции для Micropilot S FMR530

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: VeEX Страницы: 2

Бренд: WAGER Страницы: 36

Бренд: Datalogic Страницы: 6

Бренд: Datakom Страницы: 4

Бренд: Datakom Страницы: 38

PowerCross-Laser 8 S

Бренд: LaserLiner Страницы: 64

ClimaHome-Check Plus

Бренд: LaserLiner Страницы: 10

MeterMaster Plus

Бренд: LaserLiner Страницы: 104

Бренд: LaserLiner Страницы: 52

LaserRange-Master T2

Бренд: LaserLiner Страницы: 52

Бренд: LaserLiner Страницы: 5

CombiRangeXtender 40

Бренд: LaserLiner Страницы: 84

SuperCross-Laser 2P

Бренд: LaserLine Страницы: 92

MoistureFinder Compact

Бренд: LaserLine Страницы: 56

LaserRange-Master Gi7 Pro

Бренд: LaserLiner Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды