Endress+Hauser Micropilot S FMR530 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 92

background image

Mounting

Micropilot S FMR533 4 to 20 mA HART

16

Hauser

3.4

Installation instructions

3.4.1

Mounting kit

In addition to the tool needed for flange mounting, you will require the following tool:
• 4 mm Allen wrench for turning the housing.

3.4.2

Installation in tank (free space)

Optimum mounting position

L00-FMR533xx-17-00-00-en-001

Standard installation

When mounting in tank, please observe engineering hints (

11) and the following points:

• Marker is aligned towards tank wall.

The marker is located clearly visible on the sensor neck of the flange.

• After mounting, the housing can be turned 350° in order to simplify access to the display and the

terminal compartment.

• The parabolic mirror must extend below the nozzle.
• Align parabolic antenna vertically.

Mounting in manway

The parabolic antenna can be mounted on a manway cover.
The manway cover must have an opening with a diameter D1 or D2 for mounting of the antenna
(refer to the following fig.). It has to be possible to remove the cover in order to mount the antenna.
The device can be mounted on the manway cover with a weld-on flange with a neck. Please
consider the maximum height of the nozzle (H max. = 200 mm (8")) for the diameter of the basis.

90°

90°

90°

90°

90°

2°

marker at flange neck

«
...
14
15
16
17
18
...
»

Содержание Micropilot S FMR530





























































































Отзывы:

Нет отзывов

Похожие инструкции для Micropilot S FMR530

Бренд: Vcheck Страницы: 31

Бренд: Eagletone Страницы: 2

Бренд: VeEX Страницы: 2

Бренд: Datavideo Страницы: 26

Бренд: Datcon Страницы: 84

Бренд: NARDA Страницы: 64

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: QUNDIS Страницы: 20

Бренд: R&S Страницы: 2

Бренд: Saluki Страницы: 312

Бренд: Valhalla Scientific Страницы: 43

Бренд: Abus Страницы: 168

Бренд: OHAUS Страницы: 76

Бренд: lanry Страницы: 2

Бренд: lanry Страницы: 29

Бренд: Burkert Страницы: 192

Бренд: Jenoptik Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды