Endress+Hauser Micropilot S FMR530 Скачать руководство пользователя страница 55

Страница: 55 / 92

Micropilot S FMR533 4 to 20 mA HART

Commissioning

Hauser

Note!
• The offset should

not

be determined and entered within the close range of the antenna (conf.

definition of the safety distance) or immediately in the range of the tank bottom, because within
these ranges interferences of the radar signal may occur.

• The dip table can be printed out using FieldCare. Before doing this, FieldCare must be

reconnected to the device in order to update the values within FieldCare.

• Make your inputs into the dip table in semi-automatic mode. We advise you to leave

auto correction

(031)

activated ("on") while you enter your inputs.

Caution!
After entering one or more points into the dip table, make sure that the dip table is activated and
left in the "

table on

" dip table mode.

Function "dip table state" (037)

This function displays the dip table status.

Display:
• table on
•

table off

table on

Indicates whether the dip table is active.

table off

Indicates whether the dip table is not active.

⇒

E HAUSER

–

Содержание Micropilot S FMR530





























































































Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot S FMR530, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot S FMR530

Отзывы:

Похожие инструкции для Micropilot S FMR530

Бренды по названию

Популярные бренды