Endress+Hauser micropilot M FMR 240 Скачать руководство пользователя страница 25

Страница: 25 / 112

Micropilot M FMR 240 with PROFIBUS PA

Mounting

E Hauser

3.4.5

Installation FMR 240 with Wave Guide antenna

Optimum mounting position

L00-FMR240xx-17-00-00-de-003

Standard installation

For installations in a stilling well, follow the engineering hints on Page 14 and note the
following points:

•

Can be mounted in a tank or bypass.

•

No alignment is required.

•

After mounting, the housing can be turned 350° in order to simplify access to the
display and the terminal compartment.

•

Only suitable for media with low viscosity (

≤

500 cst), without the tendency for

build-up in the Wave Guide antenna.

•

No minimum distance is required between the Wave Guide antenna and the tank
bottom for measuring-related purposes.

Note!
In the event of horizontal stress (e.g. agitators) , mechanical support is required or
provide the Wave Guide antenna with a protective pipe.

Содержание micropilot M FMR 240

















































































































Результаты поиска

Содержание micropilot M FMR 240

Отзывы:

Похожие инструкции для micropilot M FMR 240

Бренды по названию

Популярные бренды

Endress+Hauser micropilot M FMR 240, Руководство по эксплуатации

Результаты поиска

Содержание micropilot M FMR 240

Отзывы:

Похожие инструкции для micropilot M FMR 240

Бренды по названию

Популярные бренды