Endress+Hauser micropilot M FMR 240 Скачать руководство пользователя страница 23

Страница: 23 / 112

Micropilot M FMR 240 with PROFIBUS PA

Mounting

E Hauser

3.4.4

Installation in bypass

Optimum mounting position

L00-FMR230xx-17-00-00-en-007

Standard installation

For installations in a stilling well, follow the engineering hints on Page 14 and note the
following points:

•

Marker is aligned perpendicular (90°) to tank connectors.

•

The marker is always exactly in the middle between two bolt-holes in the flange.

•

After mounting, the housing can be turned 350° in order to simplify access to the
display and the terminal compartment.

•

The horn must be aligned vertically.

•

Measurements can be performed through an open full bore ball valve without any
problems.

Recommendations for the bypass pipe

•

Metal (no plastic or enamel coating)

•

Constant diameter

•

Select horn antenna as big as possible. For intermediate sizes (i.e. 95 mm) select next
larger antenna and adapt it mechanically (FMR 230 / FMR 240 only).

•

At any transition (i.e. when using a ball valve or mending pipe segments), no gap may
be created exceeding 1 mm (0.04").

•

In the area of the tank connections (~ ±20 cm / 8“) a reduced accuracy of the
measurement has to be expected.

Содержание micropilot M FMR 240

















































































































Результаты поиска

Содержание micropilot M FMR 240

Отзывы:

Похожие инструкции для micropilot M FMR 240

Бренды по названию

Популярные бренды

Endress+Hauser micropilot M FMR 240, Руководство по эксплуатации

Результаты поиска

Содержание micropilot M FMR 240

Отзывы:

Похожие инструкции для micropilot M FMR 240

Бренды по названию

Популярные бренды