8-66
6205s2 BATHYMETRIC AND SIDE SCAN SONAR
0025262_REV_A
5.
Now, plug in the devices into COM 1, COM 2, and COM 3. The Gyro should be connected to COM1,
the MRU COM2, and the GPS to COM3. The devices connected to COM1 or COM2 may be
interchanged, but the GPS must be connected to COM3.
6.
Click
Misc.
at the top of the Sonar screen, as shown in
, then
Serial Port Information.
7.
Check COM1 and set the correct baud rate for that device using the dropdown menu shown in
blue, as shown in
. When the correct baud rate is set, the
State
should say
OK,
and
Errors
should not be increasing, as shown in
circled in green. The correct data string
should also be scrolling in the lower part of the window, as shown in
green arrow.
8.
Check COM2 and set the correct baud rate for the other device as done before in Step 6.
a.
Remember to check COM3 as before and set the correct baud rate for GPS.
9.
Click on
File
>
Show Status
in the sonar window, as shown in
circled in red.
10.
On the right-hand side of the window, click on the
Config
bullet under the
Update
button and
then on the dropdown menu named
Config Item
, as shown by the green arrow in
11.
Select Serial (green arrow), then click on the Update button several times (blue arrow) in
12.
Check to make sure sensors' usage percentages are well below 80%, as shown in
circled in purple. If they are not, increase the sensor’s baud rate. Change baud rate under Serial
Port Information as done in steps 6 and 7. Check Status again; otherwise, sonar will report errors.
13.
When satisfied with incoming data, press
OK
in the ‘System Status’ window, as shown in
14.
Finally, close the Sonar - 192.9.0.101 - Remote Desktop Connection window.
NOTE:
If this window is left open during data acquisition, the user may
experience a very slow computer. This is because the remote desktop
application uses a large amount of the link capacity to stay open. So it is
always good to close the remote desktop application when finished with
the configurations.
Содержание 6205S2
