Edgetech 6205S2 Скачать руководство пользователя страница 3

Страница: 3 / 108

iii

ATTENTION – READ THIS FIRST!

Warnings, Cautions, and Notes

Where applicable, warnings, cautions, and notes are provided in this manual as follows:

WARNING!

Identifies a potential hazard that could cause injury or

death.

CAUTION!

Identifies a potential hazard that could damage equipment or

data.

NOTE:

Recommendations or general information that is particular to the

presented material.

All personnel involved with the installation, operation, or maintenance of the equipment described in this

manual should read and understand the warnings and cautions provided below.

CAUTION!

This equipment contains devices that are extremely sensitive

to static electricity. Therefore, extreme care should be taken when

handling them. Normal handling precautions involve using anti-static

protection materials and grounding straps for personnel.

WARNING!

High Voltage may be present in all parts of the system.

Therefore, use caution when the electronics are removed from their

containers for servicing.

CAUTION!

Operation with improper line voltage may cause serious

damage to the equipment. Always ensure that the proper line voltage is

used.

Содержание 6205S2













































































































Результаты поиска

Содержание 6205S2

Отзывы:

Похожие инструкции для 6205S2

Бренды по названию

Популярные бренды

Edgetech 6205S2, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S2

Отзывы:

Похожие инструкции для 6205S2

Бренды по названию

Популярные бренды