ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 86 / 88

• APPLIANCE -

Device to convert gas into energy; term

includes any component, control, wiring, piping or tubing

required to be part of the device.

• ANSI

- American National Standards Institute, Inc.

Oversees creation and maintenance of voluntary

consensus standards, including ANSI Z21.13/CSA 4.9:

Gas-Fired Low Pressure Steam and Hot Water Boilers.

• ASTM

- American Society for Testing and Materials.

ASTM International is one of largest voluntary standards

development organizations in world trusted source for

technical standards for materials, products, systems, and

services. Known for their high technical quality and market

relevancy, ASTM International standards have important

role in information infrastructure that guides design,

manufacturing and trade in the global economy.

• AUTHORITY HAVING JURISDICTION

Individual or

organization adopting and enforcing codes, rules, and by-

laws governing various concerns of community. Commonly

referred to as "final authority" for any matters relating

to LIFE SAFETY and BUILDING CONSTRUCTION within a

community.

• BOILER

- Appliance intended to supply hot liquid for space-

heating, processing or power purposes.

• Btu

- Abbreviation for British Thermal Unit. Quantity of heat

required to raise temperature of 1 pound of water 1°F.

• BURNER

- Device for final conveyance of gas or mixture of

gas and air, to combustion zone.

• CALIBRATE

- Make fine adjustments or divide into marked

intervals for optimal measuring.

• COMBUSTION

- Rapid oxidation of fuel gases accompanied

by production of heat or heat and light. Complete combustion

of fuel is possible only in presence of adequate supply of

Oxygen.

• COMBUSTIBLE MATERIAL

- Materials made of or surfaced

with wood, compressed paper, plant fibers, or other

materials capable of being ignited and burned. Such

material shall be considered combustible even though flame-

proofed, fire-retardant treated, or plastered.

• COMBUSTION AIR

- Air that is drawn into an appliance to

mix with fuel and support combustion.

• CONDENSATE

- Liquid separated from flue gas due to

reduction in temperature.

• DIRECT VENT BOILER

- Boiler constructed and installed so

all combustion air is derived directly from outdoors and all

vent gases are discharged to outdoors.

14 - GLOSSARY

• GAS SUPPLIER -

Party that sells commodity of Natural Gas

(Gas A) or LPG (Gas E).

• HIGH-VOLTAGE

- Circuit involving potential of not more

than 600 volts and having circuit characteristics in excess of

those of low-voltage circuit.

• IGNITER

- Device utilizing electrical energy to ignite gas at

main burner.

• LEAK CHECK

- Operation performed on gas piping system

to verify system does not leak.

• LICENSED QUALIFIED INSTALLER / SERVICE

TECHNICIAN -

any individual, firm, corporation or

company that either directly or through a representative is

engaged in the installation, replacement, repair or servicing

of gas piping, venting systems, appliances, components,

accessories, or equipment, and whose representative is

experienced and trained, in such work and has complied

with the requirements of the authority having jurisdiction.

• LOW WATER CUTOFF

- Device constructed to automatically

cut off fuel supply when surface of water in boiler falls to

lowest safe water level.

• LOW-VOLTAGE

- Circuit involving potential of not more

than 30 volts.

• METRIC GAS METERS
Natural Gas

MBH

127,116 x cu meters
Seconds

For example: Gas Meter measures 0.1 cubic Meters in 100

seconds

MBH

127,116 x 0.1

= 127 MBH

100

Propane Gas (LP)

MBH

383,482 x cu meters
Seconds

• DOMESTIC -

Relating to household usage as opposed to

commercial usage.

• DOMESTIC WATER -

Potable drinking water - tap water.

• DRAFT

- Pressure difference causes gases or air to flow

through a chimney, vent, flue or appliance.

• FLA

- Full load amps.

• FLUE

- Enclosed passageway for conveying combustion

gases.

• FLUE GASES

- Products of combustion plus excess air in

appliance flues or heat exchanger.

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды