ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 24 / 88

6 - COMBUSTION AIR AND VENT PIPING

FIGURE 6-5 - Two Pipe Polypropylene System

Adapter

FIGURE 6-6 - Separated Horizontal Flue Termination

Boiler

Note

If using indoor air for combustion do not exceed
100ft (30m) exhaust vent pipe.

Elbow

Total Length Reduction

45°

10" (0.3 m)

90°

2 ft (0.6 m)

Twin Pipe Maximum Vent Lengths (See Figure 6-6)

Intake Vent

49 ft (15 m)

Exhaust Vent

51 ft (15.5 m)

Combined Vent

L1+L2

100 ft (30.5 m)

Note

Do not count first elbow against maximum vent

length.

WARNING

Asphyxiation hazard! For Duravent polypropylene

twin pipe only. The twin pipe vent connections on

the 380 boiler are designed to accept 110 mm.

DuraVent polypropylene 4” venting measures 100

mm.
Manufacturer requires transition pieces from

Duravent to adapt from 110 mm to 100 mm. One

transition is required for the exhaust and one is

required for the fresh air intake.
Failure to follow these instructions could result in

death or serious injury.

WARNING

Asphyxiation hazard! Improper installation could

result in death or serious injury. Read Twin Pipe

Installation Instructions completely and understand

all requirements before beginning installation.

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды