ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 60 / 88

9.17 Status And Sub-Status

The information menu

gives the following status and sub-status information:

9 - START UP PROCEDURE

State (St)

Sub-status (Su)

Rest

Boiler starts (Demand for

heat)

Short pre-purge of the fan

Control three-way valve

Start pump

sw checks sensor temperatures before the burner starts

Burner start

Open flue gas damper/external gas valve

Increase fan speed

Pre-purge

Wait for release signal from RL connection

Burner on

Pre-ignition

Ignition

Flame detection

Intermediate ventilation

Burner on (heating mode)

Temperature control

Limited temperature control (ΔT safety)

Output controlled by 0-10 v signal

Temperature protection gradient level 1 (Modulate down)

Temperature protection gradient level 2 (low-fire)

Temperature protection gradient level 3 (Blockage)

Modulate up for flame control

Temperature stabilization time

Cold start

Burner on (DHW mode)

Temperature control

Limited temperature control (ΔT safety)

Output controlled

Temperature protection gradient level 1 (Modulate down)

Temperature protection gradient level 2 (low-fire)

Temperature protection gradient level 3 (Blockage)

Modulate up for flame control

Temperature stabilization time

Cold start

Burner stop

Burner off

Post-purge

Close flue gas damper/external gas valve

Recirculation protection (checks to see if gas valve has closed)

Fan Stops

Boiler stops (End of heat call)

Pump post circulation

Pump off

Control three-way valve

Short-cycling counter activates

Stop

Wait for burner start

Short cycling protection function

Lock-out

Shutdown codexx

Deaeration/ air purge

Rest

Control three-way valve

Start pump

Pump off

Control three-way valve

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды