ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 70 / 88

13 - TROUBLE SHOOTING

Error Code Table

Error

Code

Description

Probable Causes

Checking/Solution

E37

Communication error with

SU PCB

Bad connection

Check whether the SU PCB has been correctly fitted in

connector on PCU PCB

E38

Communication error with

SCU PCB

Bad connection

Defective SCU PCB

Check the wiring Replace SCU PCB

E39

Shutdown input in locked-

out mode

Bad connection

External problem

Parameter incorrectly set

Check the wiring

Find external problem

Check the parameters

(CHART 8)

E40

HRU unit test error

Bad connection External

problem Parameter incorrectly

set

Check the wiring

Find the external problem

Check the parameters

(CHART 9)

E41

No water temperature

change during deaeration/

air purge

Bad connection

Supply/Return sensor

damaged

No water circulation

Check the sensor connection

Replace sensor

Check the pump connection

E42

Low water cutoff

disconnected or water

pressure too low

Bad connection Water

pressure low

Check the wiring

Refill the system

Check for leaks

(CHART 10)

E43

No water temperature

change during boiler

operation (burner on)

Bad connection

Supply/Return sensor

damaged

No water circulation

Check the sensor connection

Replace the sensor

Check the pump connection

(CHART 11)

E44

Difference between supply/

return temperature too high

Bad connection

Supply/Return sensor

damaged

No water circulation

Check sensor connection

Replace sensor

Check pump connection

13.2 Shutdowns and Lock-outs

Blockage

If a blockage condition continues to exist after several start

up attempts, boiler will switch into lock-out (fault) mode. The

boiler can only start operating again once cause(s) of the lock-

out have been rectified and after pressing

button.

Lock-out Mode

A temporary lock-out caused by an unusual occurrence in the

boiler's operation. E.g. Display gives code of blocked flue

(code St9). Boiler control will try to re-start several times.

Boiler will start up again after blocking condition(s) have been

eliminated.
Shutdown codes can be read out as follows:

• Press the two buttons

simultaneously.

•

Confirm by pressing

button.

"St"

is displayed,

alternating with the shutdown code

"9"

• Press the

(+)

button.

"Su"

appears on the screen.

Boiler will start again automatically when reason for blocking

has been removed.

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды