ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 5 / 88

1 - IMPORTANT INFORMATION

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in death or serious injury.

This is the safety alert symbol. Symbol alerts you

to potential personal injury hazards. Obey all safety

messages following this symbol to avoid possible

injury or death.

Become familiar with symbols identifying potential hazards.

Boiler installation shall be completed by qualified agency. See

glossary for additional information.

1. Safety Information

WARNING

Do not tamper with or use this boiler for any purpose

other than its intended use. Failure to follow these

instructions could result in death or serious injury.

Use only manufacturer recommended parts and

accessories.

CAUTION

Laceration, burn hazard. Metal edges and parts

may have sharp edges and/or may be hot. Use

appropriate personal protection equipment to include

safety glasses and gloves when installing or servicing

this boiler. Failure to follow these instructions could

result in minor or moderate injury.

WARNING

Fire, explosion, asphyxiation and electrical shock

hazard. Improper installation could result in death or

serious injury. Read this manual and understand all

requirements before beginning installation.

FOR YOUR SAFETY READ BEFORE OPERATING

Hot Water Can Scald!

Water heated to temperature for clothes washing,

dish washing and other sanitizing needs can scald

and cause permanent injury.

Children, elderly, and infirm or physically handicapped

persons are more likely to be permanently injured by

hot water. Never leave them unattended in bathtub or

shower. Never allow small children to use a hot water

tap or draw their own bath.

If anyone using hot water in the building fits the

above description, or if state laws or local codes

require certain water temperatures at hot water

taps, you must take special precautions:

• Use lowest possible temperature setting.

• Install some type of tempering device, such

as an automatic mixing valve, at hot water

tap or water heater. Automatic mixing valve

must be selected and installed according

to manufacturer's recommendations and

instructions.

• Water passing out of drain valves may be

extremely hot. To avoid injury:

• Make sure all connections are tight.

•

Direct water flow away from any person.

DANGER

Water

Temperature

Setting

1st Degree Burn

Exposure Time For

An Adult

2nd and 3rd Degree Burn

Exposure Time For An

Adult

120° F

1 minute

5 minutes

130° F

5 seconds

30 seconds

140° F

2 seconds

5 seconds

150° F

1 second

1.5 seconds

160° F

Instantaneous

0.5 seconds

Note:

Warning for Infants, Children, and Elderly: Great

care must be taken when exposing the aforementioned

groups to warm or hot water as they can be badly burned

in exposure times less than half of the time for an adult.

Note

Used to address practices not related to
personal injury.

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды