ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 87 / 88

• PRESSURE TEST

- Operation performed to verify gas

tight integrity of gas piping following its installation or

modification.

• PURGE

- To free gas conduit of air or gas, or mixture of gas

and air.

• PURGE TIME

- Period of time intended to allow for

dissipation of any unburned gas or residual products of

combustion.

• QUALIFIED AGENCY

- Any individual, firm, corporation, or

company engaged in and responsible for:

• Installation, testing, or replacement of gas piping, or

connection, installation, testing, repair or servicing

of appliances and equipment.

•  Experienced in such work.
•  Familiar with all precautions required.
•  Complies with all requirements of authority having

jurisdiction.

• SAFETY RELIEF VALVE

- Valve designed to relieve

pressure in hot water supply system when pressure exceeds

pressure capability of equipment.

• SAFETY SHUTOFF DEVICE

- Device that will shut off gas

supply to controlled burner in event source of ignition fails.

• SEDIMENT TRAP

- Gas piping arrangement designed to

collect any liquid or solid contaminant before reaching gas

valve.

• SERVICE

-Supply, installation, or maintenance of goods

carried out by a Qualified Installer / Service Technician.

• TWO PIPE SYSTEM

- Type of venting that allows for

exhaust flue and intake air piping to be separated from each

other. Fresh air may be drawn in at a different area from

where flue terminal is located.

• VENT

- Passageway used to convey flue gases from

appliance vent connector to outdoors.

• VENTING SYSTEM

- Continuous open passageway from

of appliance vent connector to outdoors for purpose of

removing flue or vent gases.

15 - GLOSSARY

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды