ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 79 / 88

Is this a new boiler on first startup?

YES

LP Conversion Kit installed?

YES

Connect All Wires And

Assure Secure Fit

Open the gas shutoff

valve

E14

- Burner Start Up

Failures

LP installation?

YES

Troubleshooting Chart 5

Check all wires including

igniter and gas valve are

connected and tight

YES

Check Gas Line For Obstructions

Install

Conversion Kit

Is the gas shutoff valve closed?

YES

13 - TROUBLE SHOOTING

Are ground wires attached and boiler

properly grounded?

YES

Provide Proper

Ground

Has all air been purged

from gas line?

YES

Purge all air

from gas line

Check gas inlet pressure at least

equals rating plate requirements.

YES

Press RESET for two (2) seconds and retry.

Is there a strong, consistent spark?

YES

Remove igniter and inspect. Is

there contamination?

YES

Clean Or Replace Igniter

Does the boiler ignite?

YES

Restart the boiler and place into high fire

chimney sweep. Go to display and check

flame current. Is there at least 3 mA?

YES

Hold the igniter and retry

ignition. Is there a spark?

YES

Check Venting For Obstruction And

Or Wind Effects

Replace Spark

Generator

Remove burner and inspect. Any

sign of damage to burner surface?

YES

Check interior of heat exchanger for

debris or other signs of blockage

YES

Replace Burner

Replace Gas Valve

Clean Heat Exchanger

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды