ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 51 / 88

Display

[Escape] or RESET button

Heating Temperature or [-] button

DHW temperature or [+] button

[Enter] or cancel

lock-out button

Setup buttons (press the 2 and 3

buttons simultaneously)
[Menu] buttons (press the 4 and 5

buttons simultaneously)

ON/OFF switch

9 - START UP PROCEDURE

9.5 Control Panel

Symbols

Information menu:

Reading the various current values

Chimney-sweeping position:

Forced full or part

load for CO2 measurement.

User menu:

Parameters at user level can be

changed.

Heating program deactivated:

The heating

function is deactivated.

Manual mode:

Boiler is set to manual operation.

DHW program deactivated:

DHW mode is deactivated.

Service menu:

Parameters at installer level can be

changed.

Energy-saving mode:

Economic mode activated.

Fault:

Boiler fault indicated.

Can be seen from é code and red display.

Frost protection:

Boiler running in frost protection mode.

Hour counter menu:

Readout of operating hours,

number of successful starts and hours on main supply.

ON/OFF switch:

After 5 lock-outs, boiler must be

switched OFF/ON again.

Boiler pump:

Pump operates

Heating system function:

Access to heating system

temperature parameter.

DHW function:

Access to potable hot water

temperature parameter.

Yellow display with symbols:

+ s

(Maintenance message).

Water pressure:

Water pressure is too low.

Burner Level:

Boiler is running at full or low load.

Locking keys:

Key lock-out is activated.

https://image.freepik.com/free-icon/double-wrench-outline_318-44667.jpg[10/14/2016 11:44:32 AM]

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды