ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 45 / 88

8 - ELECTRICAL CONNECTIONS

8.9 K Ohm (1K

Ω) Outdoor Temperature Sensor

Outdoor Temperature

• Outdoor Sensor, if used.

A. Provided with boiler.

B. Locate 1 K

Ω outdoor sensor to protect against

wind and direct sunlight. Mounting instructions

provided with sensor.

C. Maximum wire length is 100 ft (30m) for 22 ga.

wire, or 150 ft (45m) for 18 ga. wire.

Connect wires to OUTDOOR SENSOR terminals.

Wires are interchangeable.

E. Outdoor temperature sensors are a boiler accessory.

Where there is an on/off thermostat, boiler will control

the temperature with set point of the internal heating

curve.

8.10 Central Heating Thermostat

A. If a room thermostat with an anticipator is used,

parameter

must be adjusted.

B. Install thermostat in frequently occupied room.
C. Connect 2 wire dry contact room thermostat to

ON/OFF-OT terminals of boiler's control board

connection.

Note

:ON/OFF-OT terminals are NOT

able to supply 24V to the thermostat.

D. Use thermostat or boiler system control with dry

contacts related 0.5 amps @ 120 VAC.

Boiler

control does

NOT

provide 24 VAC power to central

heating thermostat.

E. Locate and install thermostat per manufacturer's

instructions. Maximum wire length is

330 ft (100m)

for 22 ga. wire.

Connect wires to on/off - OT terminals. Wires are

interchangeable.

Boiler is not suitable for Nest type thermostat

without the use of an isolation relay, such as Argo

IR-882.

FIGURE 8-10 Outdoor Temp Sensor

FIGURE 8-11 1k Ω Outdoor Temp Sensor Chart

Note

Use dry contact for wires to On/Off OT terminal.

E33

error code is displayed if voltage is sent

back to the control board. If error is not
corrected for extended period of time, this
voltage can permanently damage control board.

If room thermostat with anticipator is used,
parameter

must be adjusted.

Note

Flow Temperature

- Supply temperature (maximum)

P25 -

Supply temperature (minimum)

P26

- "WWSD" (Warm Weather Shutdown)

P27

Outdoor temperature (default)

If outdoor temperature sensor is connected, heating curve can

be adjusted. Setting can be modified using parameters -

P25

P26

and

P27.

Note

Sensors supplied with this product are proprietary
to the manufacturer. Use of after market sensors
will result in diminished performance.

1 K

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды