ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 32 / 88

6.10 Multiple Boiler Venting - General

• For common exhaust system DuraVent

is the only

approved vent manufacturer - DuraVent

. Use of check

valve is mandatory.

• See Figures 6-26, 6-27 and 6-28. Termination

must

vertical through the roof. Sidewall horizontal terminal not

allowed.

• On multiple venting applications ensure minimum

downward slope of 2 in (50.00 mm) for every 3 ft 4 in

(1.00 m) of duct length toward boiler.

• Manufacturer recommends use of CO monitor, calibrate

regularly per CO monitor manufacturer instructions.

•  Place pipes at least 1 in (30 mm) from heat sources.
•  Keep area clean and free of debris.
•  On multiple venting applications use only water (H

O) as

lubricant when inserting pipes together. Do NOT use any

type of grease or similar substances.

•

Do NOT use screws to secure pipes together.

• Before securing pipe with clamps, verify pipe is inserted per

vent manufacturer instructions.

• Install steel strapping (A) of pipe (B) distance of 10 in

(250.0 mm) from boiler.

•

Secure flue pipe to wall with supports 3 ft. (1 meter) from

each other. Secure supports along the joint of each pipe.

6.11 Multiple Boiler Venting - Mounting Procedure -

See Figures 6-21 thru 6-23

Vent pipes correctly mounted. See Figure 6-22.

Line horizontal common vent pipes with male end towards

condensate collector end cap.

Follow vent manufacturer's instructions when assembling

vent pipe to allow for expansion and contraction of vent

pipe during use.

Hang horizontal common vent pipe, do not fully tighten

clamps down.

WARNING

Asphyxiation hazard. DO NOT use screws to secure

piping together. Failure to follow these instructions

could cause death or serious injury.

6 - COMBUSTION AIR AND VENT PIPING

L > 10 in
(250 mm)

FIGURE 6-21 Correctly Mounted Piping

FIGURE 6-22 Correctly Mounted Piping

FIGURE 6-23 Correctly Mounted Piping

WARNING

Cascade venting of condensing boilers shall be

vented with Duravent

polypropylene venting

material. Failure to follow these instructions could

result in death or serious injury.

USE OF CHECK

VALVE IS

MANDATORY

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды