background image

 

TURBOMAX 

®

Instantaneous Indirect Water Heater  

 

USE & CARE MANUAL 

WITH INSTALLATION INSTRUCTIONS FOR THE CONTRACTOR 

 

 

 

Your TURBOMAX

®

 Instantaneous Indirect Water Heater has been carefully assembled and 

factory tested to provide years of trouble-free service.  In order to insure the service intended, 
the following information is provided to enable proper installation, operation, safety 
precautions and maintenance of this product. 
  
It is imperative that all persons who are expected to install, operate or adjust this water heater 
read the instructions carefully so that they may understand how to do so.   
 
Any questions regarding the operation, maintenance, service or warranty of this water heater 
should be directed to the entity from whom it was purchased.  
 
When all installation steps have been completed, replace this installation manual in its original 
envelope, and keep in a safe place for future reference. 

 

Note: Copyright 2005. Thermo 2000 Inc. All rights reserved. Turbomax® is a registered trademark of Thermo 2000 Inc. 
Thermo 2000 reserves the right to modify at any time and without notice colors, components, materials, specifications or 
model described in or shown in this document. 

 

Revision : July 2014  

 

 

THERMO 2000 INC.

Summary of Contents for VOLTMAX 23







































Reviews: