ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 6 / 88

Check our website frequently for updates: www.ecrinternational.com

Information and specifications outlined in this manual in effect at the

time of printing of this manual. ECR International R reserves the right to

discontinue, change specifications or system design at any time without

notice and without incurring any obligation, whatsoever.

2 - INTRODUCTION

2.5 Designated Use

•  Hot water heating boiler.
•  Indoor installation.
•  Closet or alcove installation.
•  Direct vent boiler or single vent pipe.
•

For use with natural gas or liquefied petroleum gases

(LP/propane).

2.6 The unit MUST NOT:

• Directly heat potable water. Indirect heating is acceptable.
• Heat water with non-hydronic heating system chemicals

present (example, swimming pool water).

• Exceed 50 psig (3.44 bar) maximum allowable working

pressure, or drop below minimum system pressure 7.25

psig (.50 bar)

• Exceed 176°F (80°C) system design temperature.

2.7

Operational Features

• Modulating: 10:1 ratio.
• Integral Dual Limit.
•

Integral Low Water Pressure Cutoff.

•  Outdoor Temperature Reset.
•  Heat exchanger over heat protection.
•  Recommended system pressure (cold) 21.7 psig (1.5

bar)

2.8

CSD-1 Compliance

Consult authority having jurisdiction prior to installation.
Field source:

•

Manual reset low water cutoff. See Section 5-4.

• Manual Reset External High Temperature Limit.

2 - Introduction

2.1

Installation shall conform to requirements of authority

having jurisdiction or in absence of such requirements:

• United States

•

National Fuel Gas Code, ANSI Z223.1/NFPA 54

•

National Electrical Code, NFPA 70.

• Canada

•

Natural Gas and Propane Installation Code, CAN/CSA

B149.1.

• Canadian Electrical Code, Part I, Safety Standard for

Electrical Installations, CSA C22.1

2.2

Where required by authority having jurisdiction,

installation shall conform to Standard for Controls and Safety

Devices for Automatically Fired Boilers, ANSI/ASME CSD-1.
Additional manual reset low water cutoff may be required.

2.3 Requirements for Commonwealth of

Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not limited

to:

Installation by licensed plumber or gas fitter.

2.4 Manufacturer recommends use of Carbon

Monoxide monitor may be requirement of local

jurisdiction.

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды