ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 52 / 88

9 - START UP PROCEDURE

9.6 Deaeration Function

Note

Control performs the Deaeration function at initial
start and after a reset of a locking error and after
power up.

Before starting boiler deaeration function

must

be performed.

Rotate black cap on deaerator, located on the top of the boiler,

counter clockwise



to ensure aerator is open.

• When power is supplied to the boiler Deaeration function

starts.

• Display shows

(Deaeration) and water pressure

(Psi). See Figure 9-4.

•

Boiler pump will run on and off for up to 10 minutes.

This will purge air from the system.

• The burner will switch on for a few seconds to verify

increasing temperature on flow/return sensors.

• Boiler is ready to start in standard operation.

Repeat Deaeration function at least 3 times switching boiler on

off using

button.

AERATOR - LOCATED ON TOP OF BOILER

Pump OFF

Pump ON

FIGURE 9-3 AERATOR

FIGURE 9-4 Deaeration Function Display Readout

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды