manualshive.com logo in svg

Dräger FTS 8000, Руководство по эксплуатации

Поделиться
Скачать
Dräger FTS 8000 Скачать руководство пользователя страница 52

Operation

Edition 03 / 69 06 898

48

FTS 8000

Initial status

In the initial status the sensors are not actuated and are in the initial status condition.

Operating status display

The operating status display gives the current status of monitored units.

Warning

In the event of a warning the system continues to run normally and a warning message is 
issued via the software. The warning is issued visually in the software and can be acknowl-
edged via the control panel once the trigger for the warning has been rectified.

Alarm

There are errors that trigger an alarm without changing to emergency stop mode. For 
example, if an igniter does not start, the triggered alarm must be acknowledged via the 
control elements on the cabinet or touchscreen after the incorrect start. The next ignition 
attempt can then be started.
There are alarms that result in emergency stop mode. Every error that resulted in the 
triggering of an alarm must be rectified.

Graphic

Description

Gray background and gray icon or red/yellow 
emergency stop switch icon: 

Sensor not activated

Graphic

Description

Gray background and green icon:

 

Sensor activated

Graphic

Description

Flashing yellow background and yellow icon:

New warning present

Flashing yellow background and yellow icon:

Acknowledged warning present

Yellow background and gray icon: 

Trigger for the warning is no longer present

Graphic

Description

Flashing red background and red icon or gray/yellow 
emergency stop switch icon: 

New alarm present

Lit red background and red icon:

Acknowledged alarm present

Red background and gray icon or red/yellow 
emergency stop switch icon: 

Trigger for the alarm is no longer present

Содержание FTS 8000





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды