manualshive.com logo in svg

Dodge Ram 2004, Руководство по обслуживанию

Сервисный мануал для Dodge Ram 2004 доступен для загрузки бесплатно на manualshive.com. Руководство содержит все необходимые инструкции и рекомендации для обслуживания и ремонта вашего автомобиля. Скачайте его прямо сейчас и будьте уверены в надежности вашего автомобиля Dodge Ram 2004.

Поделиться
Скачать
background image

TEST

ACTION

APPLICABILITY

2

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Left Curtain Squib connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, DO NOT PLACE AN
INTACT UNDEPLOYED CURTAIN AIRBAG FACE DOWN ON A HARD SUR-
FACE, THE AIRBAG WILL PROPEL INTO THE AIR IF ACCIDENTALLY
DEPLOYED.
Connect the appropriate Load Tool to the Left Curtain Airbag connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
NOTE: Check connectors - Clean and repair as necessary.
With the DRBIII

t

, read active Airbag Control Module DTC’s.

Does the DRBIII

t

show LEFT CURTAIN SQUIB 1 CIRCUIT OPEN?

All

Yes

→

Go To

3

No

→

Replace Left Curtain Airbag in accordance with the Service
Information.
Perform __AIRBAG VERIFICATION TEST - VER 1.

3

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Airbag Load Tool from the Left Curtain Squib connector(s).
Disconnect the Airbag Control Module Connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool ACM Adapter to the Airbag Control Module
connector(s).
Measure the resistance of the Left Curtain Squib 1 Line 1 and Line 2 circuits between
the Load Tool ACM adaptor and the Left Curtain Squib 1 connector.
Is the resistance below 1.0 ohms on both circuits?

All

Yes

→

Go To

4

No

→

Repair open or high resistance in the Left Curtain Squib 1 Line 1
or Line 2 circuits.
Perform __AIRBAG VERIFICATION TEST - VER 1.

4

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.

All

Repair:

Replace the Airbag Control Module in accordance with the Service
information.
Perform __AIRBAG VERIFICATION TEST - VER 1.

69

AIRBAG

LEFT CURTAIN SQUIB 1 CIRCUIT OPEN —

Continued

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

JETBAG 320 Fitting Instructions Manual preview
320
Бренд: JETBAG Страницы: 44
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Бренд: FABBRI PORTATUTTO Страницы: 2
Whispbar K934W Fitting Instructions Manual preview
K934W
Бренд: Whispbar Страницы: 15
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Бренд: Safe Fleet Страницы: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Бренд: Seat Страницы: 44
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Бренд: STARLANE Страницы: 24
Road Ranger H392 Installation Manual preview
H392
Бренд: Road Ranger Страницы: 22
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
Power Acoustik METER 4 Installation preview
METER 4
Бренд: Power Acoustik Страницы: 4
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Бренд: Billien Страницы: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Бренд: Lexus Страницы: 28
Guardsman G14776S Fitting Instruction preview
G14776S
Бренд: Guardsman Страницы: 2
Buick 1995 Roadmaster Manual preview
1995 Roadmaster
Бренд: Buick Страницы: 340
BMW 325i 1991 Electrical Troubleshooting Manual preview
325i 1991
Бренд: BMW Страницы: 64
Nav TV NTV-KIT850 Install Manual preview
NTV-KIT850
Бренд: Nav TV Страницы: 11
Kargo Master 48132 Instruction Manual preview
48132
Бренд: Kargo Master Страницы: 9
AUTOTECH 10.297.300K-303K Installation Instructions preview
10.297.300K-303K
Бренд: AUTOTECH Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды