Dodge Ram 2004 Скачать руководство пользователя страница 294 | Manualshive

Страница: 294 / 642

background image

Symptom:

*NO RESPONSE FROM INSTRUMENT CLUSTER

POSSIBLE CAUSES

ATTEMPT TO COMMUNICATE WITH ANOTHER MODULE

OPEN GROUND CIRCUIT(S)

OPEN FUSED IGNITION SWITCH OUTPUT CIRCUITS

OPEN FUSED B+ CIRCUIT(S)

OPEN PCI BUS CIRCUIT

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, attempt to communicate with the Airbag Control Module.
With the DRB, attempt to communicate with the Controller Antilock Brake (CAB)
module.
Was the DRB able to I/D or communicate with any of the modules?

All

Yes

→

Go To

2

No

→

Refer to symptom list for problems related to the PCI Bus
Communication Failure.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Turn all lights off.
Disconnect the Instrument Cluster harness connectors.
Using a 12-volt test light connected to 12-volts, probe each ground circuit.
Is the test light illuminated for each circuit?

All

Yes

→

Go To

3

No

→

Repair the ground circuit(s) for an open.
Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition off.
Disconnect the Instrument Cluster harness connectors.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe each Fused Ignition Switch
Output circuit.
Is the test light illuminated for each circuit?

All

Yes

→

Go To

4

No

→

Repair the Fused Ignition Switch Output circuit for an open or
short. Refer to the wiring diagrams in the service information.
Perform BODY VERIFICATION TEST - VER 1.

280

COMMUNICATION

«
...
292
293
294
295
296
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: Raven Страницы: 24

Бренд: Weather Guard Страницы: 4

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Yakima Страницы: 8

Бренд: Ford Страницы: 2

Бренд: Kia Страницы: 10

Gold Cruuse Cruisecontrol GC90

Бренд: John Gold Страницы: 24

Бренд: Whispbar Страницы: 14

Бренд: JKS Страницы: 3

Бренд: Icom Страницы: 20

Бренд: Mitsubishi MOTORS Страницы: 416

Bluetooth Phone System 2010

Бренд: Kia Страницы: 16

Perfect Fit MBM120

Бренд: Waeco Страницы: 3

Бренд: Or-Fab Страницы: 4

IT FITS RBO1018

Бренд: RBO Страницы: 36

Бренд: Kleinn Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды