Dodge Ram 2004 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 642

background image

TEST

ACTION

APPLICABILITY

2

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Left Side Impact Sensor 1 connector.
Disconnect the Airbag Control Module connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
Measure the voltage of the Left Side Impact Sensor 1 Signal circuit and sensor 1
ground circuit at the Left Side Sensor 1 connector and ground.
Is there any voltage present?

All

Yes

→

Repair the Left Side Impact Sensor 3 circuits shorted to battery.
Perform __AIRBAG VERIFICATION TEST - VER 1.

No

→

Go To

3

3

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
Measure the resistance of the Left Side Impact Sensor 1 Signal circuit between the
Driver Side Impact Sensor 1 connector and ground.
Is the resistance below 100K ohms?

All

Yes

→

Repair the Left Side Impact Sense 1 Signal circuit shorted for a
short to ground.
Perform __AIRBAG VERIFICATION TEST - VER 1.

No

→

Go To

4

4

Measure the resistance between the Driver Side Impact Sensor Signal and Sensor
Ground circuits at the Left Side Impact Sensor 1 connector.
Is the resistance below 100K ohms?

All

Yes

→

Repair the Left Side Impact Sensor 1 circuits shorted together.
Perform __AIRBAG VERIFICATION TEST - VER 1.

No

→

Go To

5

5

Connect the appropriate Load Tool ACM Adaptor to the Airbag Control Module
connector.
Measure the resistance of the Left Side Impact Sensor 1 Ground circuit between the
Left Side Impact Sensor 1 connector and the Load Tool ACM Adaptor.
Is the resistance below 1 ohm?

All

Yes

→

Go To

6

No

→

Repair the Left Side Impact Sensor 1 Ground circuit open or high
resistance.
Perform __AIRBAG VERIFICATION TEST - VER 1.

6

Measure the resistance of the Left Side Impact Sensor 1 Signal circuit between the
Left Side Impact Sensor 1 connector and the Load Tool ACM Adaptor.
Is the resistance below 1 ohm?

All

Yes

→

Go To

7

No

→

Repair the Left Side Impact Sensor 1 Signal circuit open or high
resistance.
Perform __AIRBAG VERIFICATION TEST - VER 1.

99

AIRBAG

NO LEFT SIDE IMPACT SENSOR 1 COMMUNICATION —

Continued

«
...
111
112
113
114
115
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

ESCALADE - BROCHURE 2009

Бренд: Cadillac Страницы: 24

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

Бренд: Pivot Страницы: 4

Бренд: DAVIS Страницы: 32

Бренд: Curt Manufacturing Страницы: 6

Бренд: A-Tach Страницы: 2

Бренд: TATA Motors Страницы: 92

Бренд: SAN HIMA Страницы: 10

Бренд: Thule Страницы: 12

Бренд: Jaeger Страницы: 14

Бренд: Prorack Страницы: 13

Бренд: Westin Страницы: 3

Бренд: iSimple Страницы: 8

Бренд: Saab Страницы: 9

ProPlus 620066V01

Бренд: PAT Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды