Dodge Ram 2004 Скачать руководство пользователя страница 454 | Manualshive

Страница: 454 / 642

background image

Symptom List:

VIN CHECKSUM ERROR
VIN PREVIOUSLY STORED

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be VIN CHECKSUM ERROR.

When Monitored and Set Condition:

VIN CHECKSUM ERROR

When Monitored:

With the ignition on.

Set Condition:

Once the Instrument Cluster learns a valid VIN and another valid VIN is

transmitted on the bus. The Instrument Cluster decodes the VIN that is transmitted on
the bus by the PCM. If the VIN is valid the Instrument Cluster stores the information. If
the VIN information does not equate to the encrypted value then the fault is set.

VIN PREVIOUSLY STORED

When Monitored:

With the ignition on.

Set Condition:

Once the Instrument Cluster learns a valid VIN and another VIN is

transmitted on the bus. This code can only be set if a PCM or MIC has been exchanged or

9

swapped

9

from another vehicle. The VIN is embedded in both the cluster and the PCM and

cannot be used in any other vehicle.

POSSIBLE CAUSES

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: The V.I.N. is embedded into the Instrument Cluster memory during
production and can not be modified. Do not attempt to

(

swap

(

a cluster from

one vehicle to another. Refer to the Instrument Cluster Caution in the
Service Information.
NOTE: This code will only be set if the PCM has been exchanged or

(

swapped

(

into this vehicle from another.

If any components have been exchanged or

9

swapped

9

, reinstall the original parts.

With the DRBIII

t

, erase DTCs.

Cycle the ignition.
With the DRBIII

t

, read DTCs.

If this code resets, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

440

INSTRUMENT CLUSTER

«
...
452
453
454
455
456
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: B-Speech Страницы: 18

Бренд: Eclipse Страницы: 6

Бренд: Kathrein Страницы: 7

Porsche 911 GT3 R

Бренд: iRacing Страницы: 25

Бренд: CALIMA Страницы: 9

Бренд: T-Mobile Страницы: 2

Бренд: Toyota Страницы: 165

Бренд: Westfalia Страницы: 10

Giulietta 2.0 JTDM

Бренд: Alfa Romeo Страницы: 14

Бренд: Prime Design Страницы: 8

Бренд: Ford Страницы: 264

Бренд: Kargo Master Страницы: 9

Бренд: Buick Страницы: 394

Бренд: Yakima Страницы: 10

Бренд: Chevrolet Страницы: 357

Бренд: 70mai Страницы: 47

Бренд: Toyota Страницы: 24

Бренд: Toyota Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды