Dodge Ram 2004 Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 642

background image

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Access and disconnect the Right Rear and Left Rear Speaker harness connectors.
Disconnect the Amplifier C2 harness connecter.
Measure the resistance between ground and each of the 4 Rear Speaker circuits.
Is the resistance above 1000 ohms for each of the measurements?

All

Yes

→

Go To

4

No

→

Repair the Rear Speaker circuit that measured below 1000 ohms
for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Access and disconnect the Right Rear and Left Rear Speaker harness connectors.
Disconnect the Amplifier C2 harness connecter.
At the Amplifier C2 harness connector, measure the resistance between the Left Rear
Speaker (-) circuit and the following circuits: Left Rear Speaker (+), Right Rear
Speaker (-) and Right Rear Speaker (+).
Is the resistance above 1000 ohms for each of the measurements?

All

Yes

→

Go To

5

No

→

Repair the Rear Speaker circuits that are shorted together.
Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Access and disconnect the Right Rear and Left Rear Speaker harness connectors.
Disconnect the Amplifier C2 harness connecter.
At the Amplifier C2 harness connector, measure the resistance between the Left Rear
Speaker (+) circuit and the following circuits: Right Rear Speaker (-) and Right Rear
Speaker (+).
Is the resistance above 1000 ohms for each of the measurements?

All

Yes

→

Go To

6

No

→

Repair the Rear Speaker circuits that are shorted together.
Perform BODY VERIFICATION TEST - VER 1.

6

Turn the ignition off.
Access and disconnect the Right Rear Speaker harness connector.
Disconnect the Amplifier C2 harness connecter.
At the Amplifier C2 harness connector, measure the resistance between the Right
Rear Speaker (+) circuit and Right Rear Speaker (-) circuit.
Is the resistance above 1000 ohms?

All

Yes

→

Replace the Amplifier in accordance with the service information.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Repair the Rear Speaker circuits that are shorted together.
Perform BODY VERIFICATION TEST - VER 1.

228

AUDIO

REAR SPEAKERS SHORT TOGETHER OR TO GROUND —

Continued

«
...
240
241
242
243
244
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Multiple G9F18 AU000

Бренд: Genesis Страницы: 3

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: kincrome Страницы: 6

Бренд: Audi Страницы: 12

Бренд: EUFAB Страницы: 52

Vantage 12 Series

Бренд: Ecco Страницы: 5

Бренд: Motoalliance Страницы: 8

Бренд: AA Products Страницы: 6

Бренд: Qeedon Страницы: 2

Бренд: Mobileye Страницы: 29

Бренд: Buick Страницы: 394

Бренд: ULTIMATE SPEED Страницы: 132

Бренд: Kia Страницы: 25

Nemesis Ultra FNU200

Бренд: Purpleline Страницы: 4

2002 Civic Hatchback

Бренд: Honda Страницы: 119

Бренд: Audiovox Страницы: 7

Бренд: FORM FIT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды