Dodge Ram 2004 Скачать руководство пользователя страница 297 | Manualshive

Страница: 297 / 642

background image

Symptom:

*NO RESPONSE FROM PCM (PCI BUS) - NGC

POSSIBLE CAUSES

PCM PCI NO RESPONSE

POWERTRAIN CONTROL MODULE

PCI BUS CIRCUIT OPEN

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
NOTE: As soon as one or more module communicates with the DRB, answer
the question.
With the DRB, enter Body then Electro/Mechanical Cluster (MIC).
With the DRB, enter Passive Restraints then Airbag.
Were you able to establish communications with any of the modules?

All

Yes

→

Go To

2

No

→

Refer to symptom PCI Bus Communication Failure in the Com-
munications category.
Perform (NGC) POWERTRAIN VERIFICATION TEST VER - 1.

2

With the DRB read the Powertrain DTC’s. This is to ensure power and grounds to the
PCM are operational.
NOTE: If the DRB will not read PCM DTC’s, follow the NO RESPONSE TO
PCM (PCM SCI only) symptom path.
Turn the ignition off.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIII

t

select Pep Module Tools.

Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the appropriate terminal of special tool #8815.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

→

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform (NGC) POWERTRAIN VERIFICATION TEST VER - 1.

No

→

Repair the PCI Bus circuit for an open.
Perform (NGC) POWERTRAIN VERIFICATION TEST VER - 1.

283

COMMUNICATION

«
...
295
296
297
298
299
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

witty park XEV6 Series

Бренд: hager Страницы: 9

5TH GEN 4RUNNER

Бренд: Victory 4x4 Страницы: 5

Бренд: Keith Страницы: 2

Road Ready Seat Protector

Бренд: Wagan Страницы: 12

Бренд: Chevrolet Страницы: 50

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: ULTIMATE SPEED Страницы: 21

Бренд: Mercedes-Benz Страницы: 358

Бренд: Butts of Bawtry Страницы: 2

LineCast Auto FM

Бренд: Belkin Страницы: 15

Бренд: Rover Страницы: 285

Бренд: Xpresskit Страницы: 12

Бренд: Honda Страницы: 326

Turnoverball 1020

Бренд: Bowers & Wilkins Страницы: 6

Бренд: Kia Страницы: 25

Бренд: AL-KO Страницы: 88

Бренд: Hopkins Страницы: 4

Бренд: Fyndr Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды