Dodge Ram 2004 Скачать руководство пользователя страница 388 | Manualshive

Страница: 388 / 642

background image

Symptom:

BACKLIGHT DIMMING RX FAILURE (ACTIVE)

When Monitored and Set Condition:

BACKLIGHT DIMMING RX FAILURE (ACTIVE)

When Monitored:

With the ignition on.

Set Condition:

If the A/C - Heater Control Module does not receive the dimming function

message from the Instrument Cluster for more than 5 seconds, then the A/C - Heater
Control Module backlighting will default to full brightness and the DTC will set.

POSSIBLE CAUSES

CHECK FOR INSTRUMENT CLUSTER (MIC) DTCS

DIMMING MESSAGE NOT SEEN AT RATE EXPECTED

A/C - HEATER CONTROL MODULE

MIC - NO DIM MESSAGE TO A/C - HEATER CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t

in Body, Electro/Mech Cluster (MIC), read DTCs.

Does the DRBIII

t

display any DTCs?

All

Yes

→

Refer to the Instrument Cluster category for the related symp-
tom(s).
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

2

2

Turn the ignition on.
Turn the Headlamp switch on.
Turn the Blower control to low speed.
If equipped, press the A/C switch on.
If equipped, press the EBL switch on.
If equipped, press the Max switch on.
Rotate the Cargo Dome switch in both directions while watching the A/C (if
equipped), EBL (if equipped), and MAX (if equipped) status indicators on the
A/C-Heater Control Module.
Do the status indicators dim and brighten respectively while rotating the switch?

All

Yes

→

No problem found at this time.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

3

374

HEATING & A/C

«
...
386
387
388
389
390
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: AAMP of America Страницы: 6

Бренд: cam Страницы: 28

Бренд: RAM Страницы: 292

Бренд: RAM Страницы: 116

Бренд: Wallbox Страницы: 7

2014 Grand Cherokee SRT8

Бренд: Jeep Страницы: 596

Бренд: Skoda Страницы: 4

Бренд: Xhorse Страницы: 48

Бренд: PEUGEOT Страницы: 17

ESCALADE ESV 2005

Бренд: Cadillac Страницы: 482

Бренд: curt Страницы: 4

Бренд: Pet Gear Страницы: 4

IGNIS 2022 Series

Бренд: Suzuki Страницы: 570

Бренд: Honda Страницы: 279

Бренд: Mercedes-Benz Страницы: 284

Бренд: PIE Страницы: 2

AC-12PROWLER-FC04

Бренд: FALCON RIDGE Страницы: 9

Бренд: Huvitech Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды