Dodge Ram 2004 Скачать руководство пользователя страница 531 | Manualshive

Страница: 531 / 642

background image

TEST

ACTION

APPLICABILITY

6

Turn the ignition off.
Disconnect the Radio C2 harness connector.
Disconnect the Hands Free Module harness connector.
Measure the resistance between the Left Audio Output circuit and the Right Audio
Output circuit.
Is the resistance above 1000 ohms?

All

Yes

→

Inspect the wiring and connectors for damage or shorted circuits.
Repair as necessary. If ok, replace and program the Hands Free
Module in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Repair the Left Audio Output circuit for a short to the Right Audio
Output circuit.
Perform BODY VERIFICATION TEST - VER 1.

7

NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, wiggle the wiring
harnesses. This is to try and duplicate the failure.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

→

Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Test Complete.

517

TELECOMMUNICATION

RIGHT AUDIO INPUT SHORT TO GROUND —

Continued

«
...
529
530
531
532
533
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: IAME Страницы: 17

Бренд: Prorack Страницы: 14

DAF CHARGEMAX 90

Бренд: Paccar Страницы: 40

Бренд: GMC Страницы: 430

Giulietta 2.0 JTDM

Бренд: Alfa Romeo Страницы: 14

Бренд: Black Horse Off Road Страницы: 3

Бренд: Buick Страницы: 394

Бренд: travall Страницы: 4

Бренд: Kia Страницы: 46

Бренд: Cadillac Страницы: 538

FUEL TANK GAUGE

Бренд: VDO Страницы: 10

Бренд: ECS Electronics Страницы: 14

Бренд: U.S. General Страницы: 3

TX-STAMP-4-TC01

Бренд: Over Armour Offroad Страницы: 4

Sightline VIMCF-93C

Бренд: Crux Страницы: 2

Sightline RVCAD-81B

Бренд: Crux Страницы: 10

Бренд: Lincoln Страницы: 461

Бренд: Lotus Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды