Dodge Ram 2004 Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 642

background image

Symptom:

FCM - AMBIENT TEMP CONFIGURATION ERROR

When Monitored and Set Condition:

FCM - AMBIENT TEMP CONFIGURATION ERROR

When Monitored:

During power up.

Set Condition:

The FCM detects that an Ambient Temperature Sensor is present on the

input circuit and has gone through auto-configuration and another module is transmitting
a redundant ambient temp message.

POSSIBLE CAUSES

INCORRECT CONFIGURATION

FRONT CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: This code will only set if the FCM detects that another module
transmitting a redundant ambient temp message.
NOTE: Diagnose and repair any Communication DTCs before proceeding
with this test.
Ensure that the vehicle has only one Ambient Temperature Sensor, and that it is
hardwired to the FCM.
With the DRBIII

t

, erase DTCs.

Cycle the ignition to auto-configure the FCM.
With the DRBIII

t

, read DTCs.

Did this DTC reset?

All

Yes

→

Ensure that the vehicle is not equipped with multiple Ambient
Temperature Sensors. If vehicle is equipped with NGC, discon-
nect the ambient temp sensor to the FCM and cycle the ignition.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Replace and program the Front Control Module in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

305

COMPASS/MINI-TRIP COMPUTER

«
...
317
318
319
320
321
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: PAC Страницы: 15

Бренд: K&M Страницы: 3

Бренд: Carefree Страницы: 12

CARPOWER CAP-12XHQ

Бренд: Monacor Страницы: 5

Grand Cherokee WK2

Бренд: Jeep Страницы: 338

Бренд: DEFA Страницы: 7

Бренд: Prorack Страницы: 15

Бренд: Ironton Страницы: 7

Бренд: Trailboss Страницы: 8

MagicWatch MWE250

Бренд: Waeco Страницы: 172

Бренд: Fab Fours Страницы: 13

Бренд: v.link Страницы: 21

Бренд: GARO Страницы: 15

Бренд: Aries Страницы: 5

Бренд: Mercedes-Benz Страницы: 354

Бренд: FALCON RIDGE Страницы: 4

Бренд: Mitsubishi Страницы: 367

Бренд: PEUGEOT Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды