Dodge Ram 2004 Скачать руководство пользователя страница 411 | Manualshive

Страница: 411 / 642

background image

Symptom:

*A/C - HEATER CONTROL ILLUMINATION INOPERATIVE

POSSIBLE CAUSES

CHECK FOR INSTRUMENT CLUSTER (MIC) DTCS

INOPERATIVE BULB(S)

A/C - HEATER CONTROL MODULE

PANEL LAMPS DRIVER CIRCUIT OPEN

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t

in Body, Electro/Mech Cluster (MIC), read DTCs.

Does the DRBIII

t

display any DTCs?

All

Yes

→

Refer to the Instrument Cluster category for the related symp-
tom(s).
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

2

2

Turn the Headlamp switch on.
Rotate the Cargo Dome switch to the full brightness setting.
CAUTION: The test light must illuminate brightly. Compare the brightness
to that of a direct connection to the battery.
Using a 12-volt test light connected to ground, back probe the Panel Lamps Driver
circuit in the A/C-Heater Control Module C1 harness connector.
Does the test light illuminate brightly?

All

Yes

→

Go To

3

No

→

Go To

4

3

For Dual-Zone HVAC systems, proceed directly to the conclusion of this test and
answer Yes to the question. For Single-Zone HVAC systems, proceed as follows:
Turn the ignition off.
Remove the inoperative bulb(s) from the A/C - Heater Control Module.
NOTE: If necessary, hold the bulb in front of a lamp to see the filament.
Inspect the bulb(s).
Is each inoperative bulb Ok?

All

Yes

→

Replace the A/C - Heater Control Module in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Replace the inoperative bulb(s).
Perform BODY VERIFICATION TEST - VER 1.

397

HEATING & A/C

«
...
409
410
411
412
413
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: Ranger design Страницы: 6

Бренд: UnderCover Страницы: 16

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: METRON Страницы: 4

Бренд: Streetwize Страницы: 4

Бренд: Calix group Страницы: 4

PRIME DESIGN VCR-TC11B

Бренд: Safe Fleet Страницы: 12

Бренд: v.link Страницы: 19

Бренд: Aston Martin Страницы: 415

Бренд: Kuda Страницы: 3

EQ forfour 2018

Бренд: SMART Страницы: 224

Бренд: Buick Страницы: 58

Бренд: Uniden Страницы: 16

Бренд: Volkswagen Страницы: 188

Бренд: NavLinkz Страницы: 24

Бренд: Vauxhall Страницы: 310

Бренд: Whispbar Страницы: 17

Бренд: SAF-HOLLAND Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды