Dodge Ram 2004 Скачать руководство пользователя страница 244 | Manualshive

Страница: 244 / 642

background image

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Clockspring C1 harness connector.
Turn the ignition on.
Measure the voltage of the Radio Control MUX circuit at the clockspring C1 harness
connector.
Is the voltage above 5.0 volts?

All

Yes

→

Go To

4

No

→

Repair the radio control MUX circuit for a short to voltage
between the clockspring and the splice. If OK, replace the Clock-
spring.
Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the Clockspring C1 harness connector.
Disconnect the Instrument Cluster harness connectors.
Turn the ignition on.
Measure the voltage of the Radio Control MUX circuit at the clockspring C1 harness
connector.
Is the voltage above 5.0 volts?

All

Yes

→

Repair the Radio Control MUX circuit for a short to voltage
between the Instrument Cluster and the Clockspring.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Replace the Instrument Cluster in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the Clockspring C1 harness connector.
Turn the ignition on.
Turn the Radio on.
Connect a jumper wire between the Radio Control MUX circuit and the Ground
circuit.
Did the radio change stations?

All

Yes

→

Repair the ground circuit or the radio control MUX circuit for an
open between the clockspring and the splice. If OK, replace the
Clockspring.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

6

6

Turn the ignition off.
Disconnect the Clockspring C1 harness connector.
Measure the resistance between ground and the Ground circuit at the Clockspring
C1 harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

7

No

→

Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

230

AUDIO

REMOTE RADIO SWITCH CIRCUIT HIGH —

Continued

«
...
242
243
244
245
246
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: Kathrein Страницы: 7

Бренд: Honda Страницы: 73

Бренд: Mitsubishi Страницы: 160

Бренд: Cadillac Страницы: 442

Бренд: Mazdaspeed Страницы: 8

Бренд: Sirius Satellite Radio Страницы: 8

Green Motion DC 66

Бренд: Eaton Страницы: 18

Бренд: Veigel Страницы: 24

Бренд: Cellular Line Страницы: 25

Бренд: Vauxhall Страницы: 131

Бренд: Mobility Networks Страницы: 52

Бренд: Axxess Страницы: 8

Бренд: Dodge Страницы: 276

Бренд: AIS Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: Kia Страницы: 233

Бренд: Mercedes-Benz Страницы: 585

Бренд: Whispbar Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды