Dodge Ram 2004 Скачать руководство пользователя страница 505 | Manualshive

Страница: 505 / 642

background image

Symptom:

*RIGHT DOORS FAIL TO LOCK AND UNLOCK - QUAD CAB

POSSIBLE CAUSES

DTC PRESENT

INSTRUMENT CLUSTER - DOOR LOCK DRIVER RIGHT DOORS OPEN

DOOR UNLOCK DRIVER RIGHT DOORS WIRE OPEN

DOOR LOCK DRIVER RIGHT DOORS WIRE OPEN

DOOR LOCK MOTOR

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t

, read DTC’s.

Does the DRBIII

t

display any Door Lock related DTC’s?

All

Yes

→

Refer to symptom list for problems related to Power Door Locks.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

2

2

Turn the ignition off.
Disconnect the Instrument Cluster C1 connector.
Connect a jumper wire between the Door Unlock Driver Right Doors circuit in the
Instrument Cluster C1 connector and ground.
Momentarily connect a fused jumper wire between the Fused B+ circuit and the Door
Lock Driver Right Doors circuit in the Instrument Cluster C1 connector.
Reverse the jumper wires to drive the motors in the opposite direction.
Did the right doors lock and unlock?

All

Yes

→

Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

3

3

Turn the ignition off.
Disconnect the Instrument Cluster C1 connector.
Disconnect a right side Door Lock Motor/Ajar Switch connector.
Measure the resistance of the Door Lock Driver Right Doors circuit between the
Instrument Cluster C1 connector and the Door Lock Motor connector.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

4

No

→

Repair the Door Lock Driver Right Doors circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the Instrument Cluster C1 connector.
Disconnect a right side Door Lock Motor/Ajar Switch connector.
Measure the resistance of the Door Unlock Driver Right Doors circuit between the
Instrument Cluster C1 connector and the Door Lock Motor connector.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

5

No

→

Repair the Door Unlock Driver Right Doors wire for an open.
Perform BODY VERIFICATION TEST - VER 1.

491

POWER DOOR LOCKS/RKE

«
...
503
504
505
506
507
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: Calira Страницы: 14

Wallbox eM4 Single

Бренд: ABL Страницы: 68

Бренд: DEFA Страницы: 7

Бренд: Prorack Страницы: 15

Бренд: Whispbar Страницы: 15

01 29 9 416 497

Бренд: BMW Страницы: 5

Бренд: Harbor Freight Tools Страницы: 12

Бренд: Honda Страницы: 3

Бренд: Subaru Страницы: 2

Бренд: Subaru Страницы: 328

Бренд: Simplicity Страницы: 10

ZapCharger Portable C1

Бренд: ZAPTEC Страницы: 20

Бренд: Pontiac Страницы: 20

Бренд: ULTIMATE SPEED Страницы: 56

Dodge Caravan 2002

Бренд: Chrysler Страницы: 2399

Бренд: Ednet Страницы: 6

XC70 - ANNEXE 808

Бренд: Volvo Страницы: 8

Бренд: Stack Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды